Ring Security Cameras
Browse posts, comment, and join in the discussion about Ring’s indoor and outdoor cameras.
Floodlight Cam Lights coming on constantly
I just got and installed my first of two Floodlight cams. When I got home last night I found the light was on so I turned it off manually. The light cam back on in a few seconds. I turned it off again and it did the same thing. So, I left it by itself and it turned on then off for a few seconds and back on constantly. I checked to see if there were any alerts and there was nothing noted. My wife told me that it was doing it all night. I ended up turning the whole camera off for the night.Any ideas? I checked and I don't have a schedule and as I have stated I don't have any alerts. I turned it back on this morning and so far the light hasn't come on.
89084 •
5 •
98 •
06-10-2019 18:43:54
Responses (24)
- L
Ok guys. Disable your modes for your sensor in the application. We have been having this issue for about 24 hours now. I’ve been all over this thread. Randomly fixed by disabling the away and home modes.
•6
04-08-2020 06:20:53
WYou are the best. Thankyou.. this stopped my light from coming on.. Hey Ring...if you read this you owe this guy a free subscription..he figured out how to fix this, even if temporary ..which is way more than youve done. I was about to smaah mine off the wall and throw it in the dumpster. Thx morris
•0
10-08-2020 03:50:59
BI have this problem but it isn't with a camera. I have two of the Doorbell 2s, 6 of the Pathlight, 1 wired spotlight, and 2 battery spotlights. The doorbells are wired to the existing wiring. The lights are linked to the doorbells to record when they detect motion. The doorbells worked great-- until I added the lights. The Pathlights trigger an event like you have all described. They detect motion every 1-5 minutes , all day. This makes the doorbells record all the time. I even had to take the batteries out and charge them because they were drained to 20% from recording so much. There is no motion and I've set the sensitivities, etc. as low as they will go... no help. I can't believe that these issues haven't been addressed by Ring. I'm very close to getting rid of all the Ring products I own. What kind of security is this system providing if there are so many false alarms, the system can longer be trusted? What did we buy these for, if not for security?
•0
12-08-2020 18:52:12
- G
I found this thread after running into the issue with my second flood light install. I was able to resolve the light cycling on after each timeout by moving the LED lamps further from the PIR sensor on the bottom of the camera. My hypothesis was the LED heat syncs were triggering the lights as soon as they turned off. This immediately worked for me, not sure if it can help others but might be worth a shot.
•2
10-10-2020 02:18:45
•
SI'm having the same problem as everyone else. As soon as it gets dark one of two floodlight cams lights up and stays on. I've had my floodlights for two years and they have worked fine. I've deleted the rapid response app, reset everything...not thing seems to work. I turn off the light through the app and a few seconds later it turns on again. Someone from Ring needs to respond to this common problem!
•2
01-11-2020 05:04:26
- K
I’m experiencing the same problem as discussed by many other. Lights go on without any motion being registered. Hardwired - up to date software - reduced motion area - no heat source. Mostly I just turn it off it’s so annoying. Anyone solve this issue?
•0
16-11-2020 22:27:22
•
JI have Same problem after a couple years of working. Happened when the power was turned off and then turn back on to the light switch. Now I can’t get the fight like to stay off for any period More than 30 seconds
•0
20-11-2020 06:34:27
RGreetings all,Like others, I found my way here looking for an answer to the "constant on" of the floodlight after dark that just recently started at my location.Before I get to the point, a little background on the floodlight camera in question. It was ordered directly from ring in May of 2019, and was originally intalled to operate only as a floodlight sensor until I was able to get constant wifi access to its location (October 2019). The firmware shows that it is up to date, and until recently, (10 days or so) it has worked flawlessly.In an attempt to figure out the issue, I tried the suggested fixes in this thread, as well as putting any devices that have the ring app installed into airplane mode, and yet the issue persists. What I have discovered that works 100% of the time in my situation is to remove the internet access of the floodlight, at which point the light comes on only when it senses motion, as it had done all along. The downside to this obviously is the lack of notifications, but the light does not cycle the "on-\>off for 5 seconds-\>on" routine that it recently began doing.Suspecting someone may have been attempting remote access, I have been monitoring the inbound and outbound network traffic, and yet I can see nothing out of the ordinary. For anyone still following the thread with the same issue, I would suggest shutting wifi off for the floodlight and see if it stops the issue, and kindly respond back.
•0
23-11-2020 17:36:05
PI've had same issues as mentioned here for about a week, or at least that's when I've noticed the sporadic on and off of two of my flood cams. Following all the fixes mentioned here, I've concluded as it seems the PIR sensor has gone bad/defective as when I turned it down to minimum, the lights only flickered on and off only a few times throughout the night instead of over dozens of times. I've had no issues for the past 3.5 months with the sensor turned on to maximum, but all of a sudden it goes haywire? Contacting help is of no use as I was on with the "regular" tech support for an hour as they were no use, and failed to reach the tier 2 on numerous occasions, and finally hung up with a promise I'll be contacted by them. It is obvious that the defect exists with this lengthy thread going back a couple of years, so why aren't you RING updating the firmware, or doing a recall to replace the faulty PIR sensor??? When the led finally burns out, especially for those who maybe out of the warranty period, what the ??? Plausible deniability???
•0
25-11-2020 23:12:38
RI just installed a floodlight cam and I have the same issue. However, it looks like it happens only when the light has detected some movement and switches on. Then they go off at my set time interval and a couple of seconds come back on again. That happens constantly until I go in and disable motion-activated lights. Then when the lights turn off, I set it back on again. The lights stay off until some motion is detected again and it goes through the same cycle. I have another floodlight cam that I bought earlier from Amazon and that is fine. This one came from Costco and will be going back in a couple of days if it keeps happening.
•1
27-11-2020 01:31:56
SI just bought mine from Lowes Sunday and installed today. Light came on tonight when motion detected and has not turned off. We tried all suggestions on this thread with no resolve. New to this and so far we are sorry we ever bought it. Waste of money if the light can nor be used.
•0
27-11-2020 01:56:20
- B
I have 2 sets of Floods with very little problems just installed another flood on my side yard. Every time a vehicle goes either up or down the street my lights come on. Ive turned the sensitivity all the way down and brought motion zones all the way in, yet the car headlights are no where near my floods but yet the lights keep coming on. Why would car headlights turn on floods. Resetting them did nothing still happening. What good is turning sensitivity all the way down and motion way down just to keep lights from constantly coming on. I put them in side yard to make sure nothing is in my fenced yard before I turn my dog out at night. Very frustrating. Now my front floods are doing the same thing. If a car comes up my side street and headlights come up in yard the lights go off. Setting things on people mode is a joke. A little rabbit set mine off.
•0
19-12-2020 16:01:47
•
- T
Installed ring in driveway and lights turn off and on all night. There is no movement or object like an air conditioner that should be enabling the lights. Reading on here that there is no solution, so I will have to switch to conventional flood light.Makes no sense that conventional flood lights Can do motion detection but ring cannot.
•0
29-12-2020 05:28:59
•
Didn't find an answer ?
Log in or create your Ring account to post a question and join in the on the conversation.
Community Resources
Most Helpful Members
View All
©2024 Ring LLC or its affiliates
gsam
So it seems the only solution I’ve found is to deactivate the MOTION ZONES for LIGHTS inside the Light Settings. This is the only way to retain the cameras “ability” to at least detect motion and alert you without having to actually turn the whole thing off completely. Unfortunately this means it no longer is a floodlight security camera and acts as just another dire elk camera. It worked fine for months so what happened? Was there a silent firmware update? Does anyone know if the devices auto-update without our knowledge? Maybe we can revert the update if that was the problem! I’m so sick of this issue! If I have any motion zones for the lights active, even minimized to the 140 degrees to match the cameras filed of view sensor instead of the full 270 degrees that the lights field of view is, this reduction still doesn’t aid in stopping the light from coming on on its own! I’m going to contact the support team and try to figure this out.
3
27-07-2020 04:59:48
•