Responses (2)

E
Eagle328
This is of course at your own risk. But, I've read plenty of pages online that have stated it does work. Some have even recessed them in the frames. Make sure you test the location of the magnet with the sensor before you glue it in place.
1
•
15-10-2020 20:14:54
•
Reply
B

Boone

Hi @FixMacs , Yes, and if you are curious as to what you'll find inside the magnet plastic case, I've attached pictures of it (Gen2). Just use a small screwdriver to pry off the plastic cover from its base. If you happen to have a Gen1 sensor (larger than the Gen2), another option is to use the much smaller **Ring "Slim Magnet"** version. Here's the magnet lengths: Length size comparison: Gen1 magnet : **3.2 inches** Gen2 magnet : **2.09 inches** (currently not available separately) "Slim" magnet : **1.27 inches** For "Slim Magnet": Dimensions 1.27 in. long x 0.40 in. tall x 0.20 in. wide (compared to the Gen1 magnet: Dimensions 3.2 in. long x 0.5 in. tall x 0.68 in. wide). Slim magnet IS very thin (0.20 in.) [https://shop.ring.com/products/alarm-slim-magnet](https://shop.ring.com/products/alarm-slim-magnet) You can also use almost any other magnet that is thin enough for your door frame space, as long as it is strong enough to sufficiently magnetically pull on the sensor's 'reed-switch'. I hope you find this information helpful :)

1

•

17-10-2020 03:25:34

•

Reply

F

FixMacs

I have the Gen2. Will the Slim Magnet work with the Gen2 sensor? Does the polarity of the magnet matter?

1

•

08-12-2020 01:52:26

B

Boone

> @FixMacs wrote: > > I have the Gen2. Will the Slim Magnet work with the Gen2 sensor? > > Does the polarity of the magnet matter? Hello @FixMacs , Yes! The Slim Magnet will work with the Gen2 Contact Sensor. :) No, the magnet polarity of the magnet does not matter. The magnet "pulls" the sensor's internal "reed-switch" closed regardless of polarity. The internal "reed-switch" is approximately half-way along the length of the Gen2 sensor (as opposed to the Gen1, where it is more towards one end of the sensor). So, the smaller Slim Magnet should be mounted centered along the edge for your Gen2 sensor. The Slim Magnet IS very thin (0.20 iches)! Also @FixMacs , I wanted to say 'Thank You' to you for accepting my previous reply as a solution and the Kudos are appreciated. :)

2

•

08-12-2020 04:35:44

B

Boone

If you are curious as to what you’ll find inside the magnet plastic case, I’ve attached pictures of it (Gen2). Just use a small screwdriver to pry off the plastic cover from its base. (These pics were originally in earlier post, but when the Ring Community website moved to this current new website, the transfer of these pics did not make it over here). So, I reposted.  ! 

4

•

23-03-2021 16:07:25

J

JALPak

It was quite hard to remove the magnet cover. If I screw mount it, how would I remove the cover later on if say I need to switch to upgrade to a different sensor a few years later?

0

•

20-11-2022 11:35:20

J

Justin_Ring

Hi @JALPak. To remove the cover from the magnet, you just have to pull it back, and it will come off the small bracket. I have tested this myself and was able to remove the cover on the magnet for the Contact Sensor 2nd Generation, which is mounted to my door siding with double-sided tape.

0

•

22-11-2022 17:12:31